Home > ROUTE FAQs & Tips

ROUTE FAQs & Tips

August 1st, 2015 in ROUTE 300-101 Go to comments

In this article, I will try to summarize all the Frequently Asked Questions in the ROUTE 300-101 Exam. Hope it will save you some time searching through the Internet and asking your friends & teachers.

1. Please tell me how many questions in the real ROUTE exam, and how much time to answer them?

There are 50 questions, including 4 lab-sims. You have 120 minutes to answer them but if your native language is not English, Cisco allows you a 30-minute exam time extension (150 minutes in total).

2. How much does the ROUTE 300-101 cost? And how many points I need to pass the exam?

This exam costs $300. You need at least 790/1000 points to pass this exam.

3. I passed the ROUTE exam, will I get a certificate for it?

No, Cisco does not ship ROUTE Exam certificate, it only ships you a certificate after completing the full CCNP track of 3 exams (ROUTE, SWITCH & TSHOOT) within three years. Once again we have to notice that you need to finish these three exams within three years (not nine years). Many candidates misunderstand this and think they have nine years to complete three exams.

4. Which sims will I see in the ROUTE exam?

The popular sims now are Policy Based routing sim, EIGRP OSPF Redistribution sim, OSPF Evaluation Sim and EIGRP Evaluation Sim and please notice that the IP addresses, router names may be different (it is also true for Drag and Drop questions)

5. How many points will I get for one sim?

Maybe you will get about 80 to 100 points for each sim, just like the CCNA exam.

6. In the real exam, I clicked “Next” after choosing the answer, can I go back for reviewing?

No, you can’t go back so you can’t re-check your answers after clicking the “Next” button.

7. What is the difference between the old BSCI & the new ROUTE exam?

In the new ROUTE exam, there are no IS-IS, DHCP, Multicast questions so you can ignore them if you are reading old BSCI books. In fact, DHCP & Multicast are good topics and maybe you will have a chance to learn about them in other Cisco exams.

8. Can I use short commands, for example “conf t” instead of “configure terminal”? Will I get full mark for short commands?

From the comments on this site, maybe you will get full mark for short commands. But sometimes short commands don’t work so please be careful with them. We highly recommend you should learn the full commands.

9. What are your recommended materials for ROUTE?

There are many materials for learning ROUTE but below are popular materials that many candidates recommend.

Books

CCNP ROUTE Official Certification Guide

ROUTE Student Guide

CCNP ROUTE Portable Command Guide

CCNP Route Quick Reference Sheet

Video training

CBT Nuggets

Simulator (all are free)

 

GNS3 – the best simulator for learning ROUTE

Packet Tracer

10. How much time should I spend on each sim?

You should not spend more than 15 minutes for each sim. Recall that you only have 90 minutes so if you spend 15 minutes for each sim x 4 sims = 60 minutes. The 30 minutes left is for solving 46 multiple choice & drag-and-drop questions. If you are not a native English speaker and have 30-minute expansion (ask the mentor to confirm) than you can spend 20 minutes for each sim.

11. Can I pass without doing sims?

As mentioned above, each sim will cost you from 80 to 100 points. In the real exam you will have to solve 4 sims that give from 320 to 400 points. Suppose you answer all other questions perfectly then you will get 600 to 680 points but the passing score is 790. It means that you surely fail if ignore them.

From the calculation above, if you miss only one sim the chance to pass is average but if you miss two, the chance to pass is very, very low.

12. Are the exam questions the same in all the geographical locations?

Yes, the exam questions are the same in all geographical locations. But notice that Cisco has a pool of questions and each time you take the exam, a number of random questions will show up so you will not see all the same questions as the previous exam.

13. I don’t want to lose points so should I use the “copy running-config startup-config” after finishing each lab-sim?

In the ROUTE exam, we can’t use that command so surely you will not lose any points if not using that command.

14. I passed the ROUTE exam. Do you have any site similar for CCNP exams?
We have certprepare.com for SWITCH, networktut.com for TSHOOT, voicetut.com for CCNA Voice, securitytut.com for CCNA Security, rstut.com for CCIE Written & Lab, dstut.com for CCDA. Hope you enjoy these sites too!

15. Why don’t I see any questions and answers on digitaltut.com? I only see the explanation…

Because of copyrighted issues, we had to remove all the questions and answers. You can download a PDF file to see the questions at this link: http://www.agile-bridge.com/?page=route-questions-and-answers

Is there anything you want to ask, just ask! All of us will help you.

Comments
Comment pages
1 4 5 6 7 205
  1. figesomoBiode
    February 26th, 2017

    We are a small grouping of volunteers and also opening the latest scheme inside our community. Your website offered all of us with precious information to the office on. You will have done a formidable task and our own entire community will be thankful to you.

  2. Alibaba
    February 28th, 2017

    Can anyone please post 15 question please?

  3. Anonymous
    February 28th, 2017

    any CCIE website
    ???

    like digitaltut or 9tut

  4. Mr. CCNP
    March 2nd, 2017

    Any web site for CCNA 210-250 and 210-255?

  5. Zahid
    March 3rd, 2017

    what is 149+41 ?? any one tell me please what is this ?

  6. Sam
    March 3rd, 2017

    @Zahid this a dump

  7. Passed
    March 4th, 2017

    Passed Exam.
    Used 149+41+15 Qs file only. Get files at below page.
    remove spaces:
    ccnplatestdumps.blogs p o t . c o m

  8. Anonymous
    March 5th, 2017

    Please any one assist me with 300-101 video tutorials

  9. Check
    March 10th, 2017

    Passed. 855 points.

    A lot of new questions. Approximately 15 where new to me.
    -Blocking incoming SSH Traffic
    -What does the command “ip tcp adjust mss” do?
    -Eigrp is implemented in a frame relay network but there is no adjacency. Which options cause the adjacency to come up?
    -In regards to CEF (Cisco Express Forwarding) with a highlight of a configuration snippet “valid punt adjacency”.
    -Which command enable PPPOE client and specify dial-on demand routing?
    -Which OSPF network type doesn’t require a DR election?
    -Which two DMVPN phases allows a spoke to create dynamic tunnels?
    -A question about how ALWAYS block the outbound web traffic on Saturdays and Sunday between 1:00 AM to 23:59 AM.

    I only had the 149+41 files. The rest of the questions where from the 149Q+41Q files.
    Labs were:
    OSPF Evaluation Sim
    EIGRP OSPF Redistribution Sim
    Policy Based Routing Sim
    IPv6 OSPF Virtual Link Sim
    OSPF Sim
    Pay attention to the OSPF area and OSPF ID, they were different compared to the labs.

  10. John
    March 10th, 2017

    which files you guys are referring to ? where I could find 149+41 ?I have exam next week please help.

  11. John
    March 10th, 2017

    Can anyone mail me latest dumps? I’m student and no money to buy them. please !!!

  12. Bob
    March 10th, 2017

    I am planning for CCNP Route. Suggest me for preparation and study materials and dumps.

  13. ccnpdreamer
    March 11th, 2017

    can someone please email me the latest dumps for ccnp, I’d kindly appreciate it. dsx1234567890 at gmail .com

  14. Anonymous
    March 11th, 2017

    kindly email me the latest dumps at archaudhari at g ma il dot com

  15. Monty
    March 12th, 2017

    Need Help because I failed?

    How ALWAYS block the outbound web traffic on Saturdays and Sunday between 1:00 AM to 23:59 AM. What was the right answer please?

    After the end of the Simulation, when I type “Copy Run Start”, it says no file found. Can you save any configuration at all?

  16. TheOnlyPrincess
    March 13th, 2017

    @Anonymous Feb14, 2017 – yeah thanks. Il see if il bite his selling

  17. TheOnlyPrincess
    March 13th, 2017

    @Anonymous Feb17th 2017 – dude! you have skill in feature writing! im reading your comment with full reaction. but yeah, you made a good and valid point. now, that i only have few weeks left to take this exam, reading your comment made me now cram. ouch.

  18. Frustrated
    March 13th, 2017

    I had a question about what Unicast Reverse Path Forwarding (uRPF) first checks. Although CEF must be enabled to use uRPF, I think the correct answer is that it checks the source IP address of an incoming packet against the FIB. So the correct answer is FIB for this question.
    (see Kevin Wallace book p. 714)

  19. Frustrated
    March 13th, 2017

    I had a question about which type of interface was best to use when one expected significant output from debug: VTY, AUX, SNMP, Console. I think its debatable, because I have crashed a router with debug, so personally, I’d rather be on the console then. But what does Simon (Cisco) say the correct answer is?

  20. Frustrated
    March 13th, 2017

    @Check, I looked up the ‘ip tcp adjust mss’ and came up with this:

    “The TCP MSS Adjustment feature enables the configuration of the maximum segment size (MSS) for transient packets that traverse a router, specifically TCP segments in the SYN bit set, when Point to Point Protocol over Ethernet (PPPoE) is being used in the network. PPPoE truncates the Ethernet maximum transmission unit (MTU) 1492, and if the effective MTU on the hosts (PCs) is not changed, the router in between the host and the server can terminate the TCP sessions. The ip tcp adjust-mss command specifies the MSS value on the
    intermediate router of the SYN packets to avoid truncation.”

    http://www.cisco.com/c/en/us/td/docs/ios/12_2sb/12_2sba/feature/guide/sb_admss.pdf

  21. BadBoy
    March 13th, 2017

    Guys please a need your help with the dump 183 and 15Q please my test day is coming =( thanks a million ciscoexpress87 gmail please please and thanks

  22. Monty
    March 13th, 2017

    Need Help because I failed?

    How ALWAYS block the outbound web traffic on Saturdays and Sunday between 1:00 AM to 23:59 AM. What was the right answer please?

    After the end of the Simulation, when I type “Copy Run Start”, it says no file found. Can you save any configuration at all?

  23. Sihoutte
    March 14th, 2017

    Hi,

    Please share me with correct dumps for 300-101 exam to sihouttecosta-at-gmail-dot-com. thanks in advance.

  24. Tiger
    March 15th, 2017

    I have premium access of digitaltut. Why the site is not allowing to Sign in? Not giving the option on right side panels.

  25. jumbert
    March 16th, 2017

    Hi
    How are you, could anyone help me which dump exam is valid today?
    Does anyone have the exam labs ?, this next Tuesday I going present :S
    please {email not allowed}

  26. pretty_mai
    March 17th, 2017

    Please share me the latest vce / pdf file for 300 – 101 exam- {email not allowed} thanks in advance.

  27. pretty_mai
    March 17th, 2017

    Please share me the latest vce / pdf file for 300 – 101 exam- fleshlionheart-at-yahoo-dot-com thanks in advance.

  28. Anonymous
    March 18th, 2017

    I am planning for CCNP Route. Suggest me for preparation and study materials and dumps.

  29. Nila
    March 18th, 2017

    Plz share the latest dumps file for 300 – 101 exam- chothandar79-at-gmail-dot-com

  30. jumbert
    March 18th, 2017

    i going to present the next tuesday, please i need your help….

    is this question correct?

    A network engineer has configured GRE between two IOS routers. The state of the tunnel interface is continuously oscillating between up and down. What is the solution to this problem? A. Create a more specific static route to define how to reach the remote router. B. Create a more specific ARP entry to define how to reach the remote router. C. Save the configuration and reload the router. D. Check whether the internet service provider link is stable Correct Answer: A

    thanks.

  31. Abbas
    March 18th, 2017

    Assalamualikum Guys,

    Can anyone send to me valid dumps. i have waleed sir dumps are those still valid, please confirm.
    i’m waiting for reply guys.

    syedabbaspasha at gmail.com

    no space in between.

    Jazakallah qair

  32. amartumi
    March 18th, 2017

    can anyone please help to get 15 new question for CCNP route 300-101

  33. Kip
    March 19th, 2017

    Everything you need is here, Waleed 15Q , Tagwa 41Q and 149Q:

    https://drive.google.com/file/d/0B7FseoJGGFKLOFVqbXZYWHVaNTg/view

  34. Anonymous
    March 20th, 2017

    taking the test in 2 weeks, can anyone send the new dumps, i have the vce already for the old player i think even the pdf would be good, i know theres new questions, i have older study material , send dumps to raymond gone 77 @ gmail .com PLEASE

  35. Dhanush
    March 21st, 2017

    Please send me a Valid CCNP Route 300-101 dumps…i want to do ccnp route exam as soon as possible because my work place is request my ccnp certificate before end of march.So anyone can help me plzz……….({email not allowed})

  36. dek
    March 21st, 2017

    I passed the 300-101 exam with 97.xx% rating last week and below comments are all true. Thank you for sharing your experiences, it helps a lot. To all take the exam as fast as you can before new questions will be added to their database.

    ahemd erlrofaie
    January 24th, 2017

    Hi guys, I have passed my ccnp routing exam yesterday at (23/1/2017) with score (973), actually the dumps of 149q and 41q tagwa is still valid.
    Most the question came from the 41q tagwa, so you have to study it very well,
    BUT it important to study also the dump of 183q/32q/8q because it contain a lot of questions that you will not find them in both 149q and tagwa 41q dumps, in my exam none of new questions of 183q/32q/8q came, but I recommended to studied any way
    The sim in my exam:
    -ospf eigrp redistribution
    -ospf evaluation
    -ospfv3 with virtual-link
    -ospf sim
    -policy based routing sim
    The drag and drop:
    -CHAP drag (in tagwa 41q)

    Important notes about the sims:
    Regarding to sims , you should be careful because you might find that there some minor changes in the sims (like ip addess, subnets , ospf process numbers , eigrp autonomous number and so on) so check with show run command if that possible before starting the configuration, don’t not rush to configure blindly .
    In my exam, there was some little change in ospf evaluation, I mentioning below the question with changed answer:
    The question:
    Which of the following statements is true about the serial links that terminate in R3?
    A. The R1-R3 link needs the neighbor command for the adjacency to stay up
    B. The R2-R3 link OSPF timer values are 30, 120, 120
    C. The R1-R3 link OSPF timer values should be 10,40,40
    D. R3 is responsible for flooding LSUs to all the routers on the network.
    In dumps sim you will find that the correct answer is B, but in my exam that was not true, because I found that the exam changed the link R2-R3 timers to 10,40,40 and it was point-to-point link.
    also I found The link R1-R3 timer was 30,120,120 non-broad cast link, so both of the answers A , B are wrong .
    Also D was wrong because, R3 was not the DR in all the links,
    The right answer was A, because the link R1-R3 is non-broad-cast link so neighborship should be configured manually.
    So it is important to be carful .

    Important notes about tagwa 41q dump:
    It is important to mention that in tagwa 41q dump there some questions with wrong answers, here below I mentioned the question with the wrong answers:
    Question 2
    Refer to the following configuration command.
    router(config)# ip nat inside source static tcp 172.16.10.8 8080 172.16.10.8 80
    Which statement about the command is true?
    A. Any packet that is received in the inside interface with a source IP port address of
    172.16.10.8:80 is translated to 172.16.10.8:8080.
    B. Any packet that is received in the inside interface with a source IP port address of
    172.16.10.8:8080 is translated to 172.16.10.8:80.
    C. The router accepts only a TCP connection from port 8080 and port 80 on IP address
    172.16.10.8.
    D. Any packet that is received in the inside interface with a source IP address of 172.16.10.8
    is redirected to port 8080 or port 80.
    Answer:A
    Tagawa say the right answer is A , but that wrong the right answer is B (this question came in my exam)

    Question 28
    A network engineer wants to ensure an optimal end-to-end delay bandwidth product. The delay is
    less than 64 KB. Which TCP feature ensures steady state throughput?
    A. Window scaling
    B. Network buffers
    C. Round-trip timers
    D. TCP acknowledgments
    Answer:A
    Also that wrong the right answer is B
    For the dumps, you can send me at ahmedrofaii at gmail dot com , I will be glad to send them to you freely , for routing dumps and for switching , tshoot dumps
    I wish for you good luck in your exam ? 3

  37. Anonymous
    March 24th, 2017

    pls help me dumps newest, i take exam on tomorrow, many thanks. {email not allowed}

  38. Anonymous
    March 27th, 2017

    149+41+15 is valid 100%
    Exam Questions Dumps at below page including all labs in GNS3 format. Working VCE player also included in package.

    http://rebrand.ly/ccnpr370d

  39. KD
    March 27th, 2017

    Thank you Digitaltut. Passed exam today with 9xx. Same questions as shown on this website. :)

  40. MAJ
    March 27th, 2017

    My CCNA R&S certificate will expire on 2020
    If I take CCNP routing and switching exams on 2017 for both exams with pass grades
    and I take TSHOOT exam on 2019 with pass grade.
    On this case does CCNP R&S Certificate will certify on 2019-2022 or 2017-2020?
    Thank you.

  41. anna
    March 28th, 2017

    passed my ccna 2 months ago, and i need to passe ccnp
    there is somemone can tell me the steps to follow plzz

  42. Emerano
    March 30th, 2017

    Hello.

    Passed two days ago with 9XX points.

    All of the question are in 15+149+41 and are still valid.

    Ospf eval
    No eigrp eval
    Ospfv3 sim
    Redistribution
    Pbr
    No drag and drop.

    Advice: If you add any wrong line in OSPF or EIGRP process. DON´T erase the process configuration. Just add you rectifified line. Take your time to make the labs and sims, the test question take you 2 minutes as much, and check everything before pass the next question with a ping, traffic generator o sh ip route command.

    The IOS emulated is version 15.0 , has the possibility to use the ? option in order to find the correct option. Innecesary options are listed but not implemented.

    In my opinion, I have more than 5 years in Networking, is recomended that not only memorize the answers. Try to understand how are you reading. Learn about in Academy, if you have the possibility because the previous practical experience will help you in real network. Also take your time studing books, view videos, and use GNS3 or similiar emulator.

    Thanks for the help and Goodluck.

  43. omer
    March 31st, 2017

    please provide me latest dumps as my exam is after 3 days

  44. doctor
    March 31st, 2017

    So, if a candidate has 3 years to complete the 3 CCNP exams, Route, Switch, and Tshoot, and let’s say this is accomplished after 2 1/2 years, how long does CCNP certification last ? When would the CCNP have to be recertified ?

  45. JuAn
    April 2nd, 2017

    @doctor, You will get 3 years after passing the third exam.
    I know, it seems odd. Its like bonus time in a way. I almost delayed taking my third exam because of this, but my brain was already I’m the zone so I kept pushing

  46. Anonymous
    April 3rd, 2017

    The exam questions provided here arent up to date anymore. Sadly.
    Failed my exam on friday and thinking about retrying it but cant find up to date answers anywhere.

  47. anonymous
    April 3rd, 2017

    The exam questions provided here arent up to date anymore. Sadly.
    Failed my exam on friday and thinking about retrying it but cant find up to date answers anywhere
    See forum Share your ROUTE v2.0 Experience have new questions, from the old ones come in half. I have passed very fair but I have passed.

  48. anonymous
    April 3rd, 2017

    The exam questions provided here arent up to date anymore.
    See forum Share your ROUTE v2.0 Experience have new questions, from the old ones come in half. I have passed very fair but I have passed.

  49. Anonymous
    April 4th, 2017

    DOWNLOAD VCE and PDF here
    149+41+15 is 100% good in exams

    http://rebrand.ly/ccnpr370d

  50. Passed
    April 6th, 2017

    Hello guys! 300-101 passed this week. Dumps 149 + 15 + 41 are still valid. I saw some new questions, like 5 or 6.

    ATTENTION I saw differences in OSPF SIM. The timers was switched in my exam (R2-R3 not 30/120/120)

  51. Juliet
    April 9th, 2017

    Dumps4download provide you 100% passing assurance and money back guarantee to secure your CCIE Routing and Implementing Cisco IP Routing (ROUTE v2.0) certification. We have professional expert which compiled 300-101 dumps question and answer. We never compromised our quality and success. We will provide you latest updated test engine. Get huge discount.
    For More Detail: http://www.dumps4download.com/300-101-dumps.html

  52. Punisher
    April 14th, 2017

    I have 252 questions dump and planing to sit 17th of April 2017. Contact me for more details.
    t h e s l e e p y @ y a h o o . c o m..

  53. Anonymous
    April 14th, 2017

    All dumps are HERE….
    https://drive.google.com/open?id=0B-mVpzyC-2BjNURTaW5FZnp0dk0
    Enjoy!!!! All the best….

  54. Anonymous
    April 14th, 2017

    Password is stct ………..

  55. Anonymous
    April 17th, 2017

    Thanks for sharing all dumps, password is needed to extract the rar file. Can you please share it with us?

  56. Anonymous
    April 17th, 2017

    Sorry, didn’t see your comments about the password. Once again, thanks for sharing.

  57. Blabla
    April 20th, 2017

    I downloaded the file, but password stct ……….. is not working :/ pls help

  58. Blabla
    April 20th, 2017

    Please ignore above comment, it’s working!

  59. failx2
    April 22nd, 2017

    anyone else get eigrp stub sim? the sim is really easy on here – just update the eigrp stub removing the receive-only and then update the summary route on the serial int on R4 – and ping from R4 – i thought in my sim they said ping from R2 but it didn’t have routes to R3 so i messed things up trying to get that to work. did i just misread the requirement on the exam? any input appreciated.

  60. Anonymous
    April 22nd, 2017
  61. Solomon
    April 24th, 2017

    Great share & thanks
    https://drive.google.com/open?id=0B7aA6XZDGfVHQzRiOElKZy0yVEU
    Could you please share Switch?
    Can I take both of Route & Switch within 1 day?

  62. Ram
    April 25th, 2017

    Valid dump :) thank you

  63. CCNP
    April 27th, 2017

    anyone entered the exam these days!, what is the valid dump ?
    thank you

  64. Anonymous
    April 28th, 2017

    Anyone can provide a link to download latest version of VCE (2.3.4)?

  65. Anonymous
    April 29th, 2017

    I took exam last week, there was a lot of new questions with AAA drag & drop

  66. Anony
    April 30th, 2017

    Is the dumps on this link still valid ?

    https://drive.google.com/open?id=0B7aA6XZDGfVHQzRiOElKZy0yVEU

  67. coolbee
    April 30th, 2017

    Any new ques coming ???

  68. CCNP-Route
    May 3rd, 2017

    Any body taking the exam this week ? Please post the validity of the dumps.

    And…

    If you use vce,

    The best is to download “memu” (android VM) – Download “lucky patcher apk”(Google how to install it – its like 2 clicks once memu is installed) … Go to “playstore” and download the A+ VCE … and it will “purchase” the app and even if VCE upgrades … you can also upgrade the app …

    You wont need to ever download the latest VCEs as you progress in future in cisco …

  69. Anonymous
    May 4th, 2017

    What is configuration lap in the exam ….as access list in ccna

  70. Anonymous
    May 6th, 2017

    Hi Everyone

    anyone can provide me with question please,
    send 2 amukwaananias@ gmail.com

  71. Pappy
    May 9th, 2017

    Hi all. please send me the new exam. new question (I have 149+41+15+183+56+82+32+8). I will take the exam next week my CCNA will expire on May 23. Please help me. Thank you so much. my email is paul7alejo @ gmail.com

  72. Helper
    May 9th, 2017

    Hi Pappy,
    could you share your exams? ;)

  73. CJ
    May 9th, 2017

    Guys help with the new dumps and new questions

  74. Anonymous
    May 9th, 2017

    Hello everyone, Coluld some one send me the new dumps questions to {email not allowed}, please?

  75. Anonymous
    May 9th, 2017

    rgla2008 @ hotmail .com

  76. fl
    May 9th, 2017

    can someone send me latest dumps (pdf) for 300-101 route plizz pliz and new questions mubaiwasimbarashe70 @ g m a i l . c o m

  77. nav
    May 10th, 2017

    Can someone please send me lates CCNP route dumps help will be appreciated navneet018 @ gmail.com

  78. Helper
    May 10th, 2017
  79. JAF
    May 10th, 2017

    Hi All,, anyone have A+ VCE cracked APK ? i need to update my VCE to start practising for my exams. please advise .

  80. KE
    May 10th, 2017

    Taking this tomorrow. Hopefully I am prepared!

  81. KE
    May 11th, 2017

    ^ Passed! :)

  82. Anon
    May 11th, 2017

    KE,

    What country did you test in and which materials did you use?

  83. CJ
    May 12th, 2017

    KE please tell us which dumps did you used and what labs did you find on your exams.

  84. m0ha
    May 12th, 2017

    Hi Guys,

    Passed today with 855. The labs are the same, I could use copy run start in the EIGRP stub sim, but the other labs did not accept it. Practice the labs, almost every one of them was in the exam.

    But the multiple choice questions…. Almost none of the questions from digitaltut was present in the exam. Luckily I’ve studied the CCNP ROUTE foundation guide, and I could answer most of the questions, or I could guess out of 2 possible answers… The topics:

    lot of:
    -IPv6
    -DHCPv6 (what three items can you configure under a DHCPv6 pool)
    -NAT64, NAT-PT, NPT

    Or very shitty questions, like:
    -How can you solve an issue with asymmetric routing when 2 ASA firewall are configured in Active/Active failover mode?
    Drag and Drop:
    -Authentication, Authorization and Accounting on the right, a bunch of options on the left.

    Good luck!

  85. yp
    May 15th, 2017

    @m0ha ….which vce files did you study ?? Can you share me plz ? Thank you so much !

  86. ABSI
    May 15th, 2017

    @m0ha
    you want to tell that no one MCQ came from digitaltut, and you just paased because of Foundation guide!!
    come on man!!

  87. Naven
    May 15th, 2017

    I have to agree with Moha a lot of new questions passed but definitely not the score I was aiming for 870 – better have a good background of theory

    -Redistribution sim was the same.
    -ospf sim was different R2 and R3 is a p2p so timers are 10 40 40.
    -PBR next-hop is .2
    – EIGRP sim is the same.
    -Stateless / Statefull NAT64 drag and drop.
    -AAA Drag and drop
    – Example of config for vrf mode loose – choose from options.
    – if there is congestion on network which ipsla command can be used to identify?
    – if you execute debug interface s1/0 and debug interface s0/0 which output will you see.
    – DHCP v6 questions..
    I will put in the rest as I remember

  88. ggpp
    May 16th, 2017

    Thanks a lots ! @ Naven , and did u try any vce files ??

  89. IntroVoys
    May 16th, 2017

    How to register in digitaltut to have a premium account? Thanks

  90. Anonymous
    May 16th, 2017

    Passed today with 9xx.
    Checked most of the dumps out there :))
    The ones from this guys are valid and they update them too.
    i t l i b r a r i e s .c o m (remove the spaces)
    They work with the A+ Player too which was a nice touch for me.

  91. ABSI
    May 16th, 2017

    @ Anonymous
    is what you talked about look like 149+41+15+183 ??
    because I tried to open the site (itlibraries) with no luck!!

    I will go to the exam sooon.
    so your quick response will be appreciated.

  92. ABSI
    May 16th, 2017

    @ Anonymous
    is it the same as 149+41+15+183??
    since your website is not opened
    i will go for the exam sooon
    your quick response will be appreciated….

  93. mortar@
    May 16th, 2017

    Looks like a spam

    I will try with 149+41+15+183 in the end of the month.
    Let me know if will work for you

  94. CJ
    May 18th, 2017

    Anonymous please advise which dumps you used because im writting nxt week need to prepare my self

  95. logipy
    May 20th, 2017

    Everything you need to pass the exam.
    Thank you friends of digital.tut.
    Compilation of exams and including April and May.
    http://microify.com/1pFk
    the pass is
    !aAyefgyn-7nP18rSvGvzPPv5FJbO_e8AmeieWSZZtTk

  96. KE
    May 22nd, 2017

    Sorry for the delay. I am in the US. I had OSPF, ERIGRP stub, Redistribution and PBR labs. OSPF and EIRGP simlets, and 2 D&D’s. MC were a lot of the questions that were from the more recent dumps, and reworded questions.

  97. vabchgirls
    May 22nd, 2017

    Has anyone converted the LastPass 295Q to vce? Can you post a link? Thank you!

  98. Frankie
    May 23rd, 2017

    Passed today with 839. Not what i wanted but it’s a pass. I’ve self studied with the Cisco press book, CBT nuggets vids, GNS3 and Packet Tracer, but the books and vids do not cover all the material in the exam which i find very annoying, so thanks to digitaltut and everyone who has contributed.

    Several new questions, one or two not even covered by @logipy May’s new questions.

    Labs were PBR, EIGRP Stub, OSPF redistribution and OSPF sim.

    The OSPF sim with the question on the routes from R1 and R2 to R3 – I could not see any answer that would suffice. Network types were PtP and Broadcast and the timers on both links were 10, 40, 40. Full DR/BDR relationship on Broadcast link, non for PtP. Two questions were to change the timers, one to add neighbour command, can’t recall the 4th. I spent the longest on this so be careful.

  99. Anonymous
    May 23rd, 2017

    Frankie were all the questions that you had in your exam (apart from the one or two mentioned) covered by Logipy’s dumps? Cheers.

Comment pages
1 4 5 6 7 205
  1. No trackbacks yet.